How To Jump A 2018 Jeep Compass
Have you ever found yourself in a situation where your 2018 Jeep Compass won’t start and you need to jumpstart it? Whether it’s due to a dead battery or some other issue, knowing how to properly jump a vehicle can save you time and frustration. In this article, we will guide you through the steps to safely jumpstart your 2018 Jeep Compass so you can get back on the road.
Table of Contents
- Preparation steps before jumping the Jeep Compass
- Locating the battery in the 2018 Jeep Compass
- Choosing the appropriate jump starter for the Compass
- Connecting the jump starter to the Compass
- Starting the Compass after a successful jump
- Safety precautions to keep in mind while jumping the Compass
- Frequently Asked Questions
- In Conclusion
Preparation steps before jumping the Jeep Compass
Before jumping the Jeep Compass, it is essential to follow a few preparation steps to ensure a smooth and successful jump start. The first step is to park the donor vehicle close enough to the Jeep Compass so that the jumper cables can reach both vehicles easily. Make sure both vehicles are in park or neutral with the ignition off.
Next, open the hoods of both vehicles and locate the battery terminals. Identify the positive and negative terminals on both batteries. It is crucial to connect the jumper cables correctly to avoid any damage to the vehicles or injuries. Remember, red is for positive and black is for negative.
After identifying the battery terminals, connect the jumper cables in the following order:
– Connect one end of the red cable to the positive terminal of the dead battery.
– Connect the other end of the red cable to the positive terminal of the donor battery.
– Connect one end of the black cable to the negative terminal of the donor battery.
– Connect the other end of the black cable to a metal surface on the dead vehicle, away from the battery.
Locating the battery in the 2018 Jeep Compass
To jump a 2018 Jeep Compass, you first need to locate the battery, which is typically found in the engine bay. In the case of the Compass, the battery is located on the driver’s side of the engine compartment. It is housed under a plastic cover that can easily be removed by unclasping the tabs.
Once you have located the battery, you will need a set of jumper cables and another vehicle with a charged battery. Before connecting the jumper cables, make sure both vehicles are turned off. Connect one end of the red cable to the positive terminal of the dead battery, then connect the other end to the positive terminal of the charged battery. Repeat the process with the black cable, connecting one end to the negative terminal of the charged battery and the other end to a metal surface on the dead vehicle.
After the cables are connected, start the vehicle with the charged battery and let it run for a few minutes to give the dead battery some time to charge. Once the dead vehicle starts, remove the cables in the reverse order that they were attached. Make sure to drive the vehicle for at least 20 minutes to allow the alternator to fully charge the battery.
Choosing the appropriate jump starter for the Compass
Jump starting a 2018 Jeep Compass is a simple process that can be done quickly and efficiently with the right tools. When choosing the appropriate jump starter for your Compass, consider the following factors:
- Power capacity: Make sure the jump starter has enough power to start your vehicle. Look for a model with at least 600 peak amps for a smooth jump-starting experience.
- Size and portability: Opt for a compact and lightweight jump starter that is easy to store in your vehicle and carry around when needed.
- Safety features: Choose a jump starter with built-in safety features like reverse polarity protection and overload protection to prevent damage to your vehicle’s electrical system.
Once you have selected the right jump starter for your Compass, follow these steps to jump-start your vehicle:
- Locate the battery on both vehicles and position the jump starter near the battery of the dead vehicle.
- Connect the red (positive) clamp of the jump starter to the positive terminal of the dead battery, then connect the black (negative) clamp to a metal surface on the vehicle’s frame to ground the circuit.
- Start the working vehicle and let it run for a few minutes to charge the dead battery. Then, try starting the dead vehicle. If it does not start, repeat the process or seek professional help.
By following these steps and choosing the appropriate jump starter for your 2018 Jeep Compass, you can safely and effectively jump-start your vehicle in case of a dead battery emergency. Remember to always prioritize safety and consult your vehicle’s manual for specific instructions.
Connecting the jump starter to the Compass
To connect the jump starter to your 2018 Jeep Compass, follow these steps to ensure a safe and successful jump start:
-
Locate the battery: Open the hood of your Jeep Compass and locate the battery. It is usually found near the front of the engine compartment on either the left or right side.
-
Prep the jump starter: Make sure the jump starter is turned off before connecting it to the Compass. Check the cables for any signs of damage or wear. If everything looks good, connect the positive (red) cable to the positive terminal on the battery, and the negative (black) cable to a metal surface on the engine block.
-
Start the Compass: Once the jump starter is properly connected, start the Compass and let it run for a few minutes to ensure the battery is fully charged. If the car starts successfully, disconnect the jump starter in the reverse order that you connected it. Remember to always handle the jump starter with care to avoid any accidents or damage.
By following these simple steps, you can safely and effectively jump start your 2018 Jeep Compass using a jump starter. Remember to always read the manufacturer’s instructions before using any equipment, and if you are unsure of what to do, it’s always best to contact a professional for assistance.
Starting the Compass after a successful jump
To start the compass after a successful jump, there are a few steps to follow to ensure a smooth transition. First, make sure both vehicles are turned off and the jumper cables are securely connected to the battery terminals. Next, start the working vehicle and let it run for a few minutes to charge the dead battery. Once the working vehicle is running smoothly, attempt to start the Jeep Compass.
If the Compass does not start right away, give it a few more minutes to charge the battery. Sometimes, a dead battery may take a bit longer to re-energize. If the Compass still does not start after a few attempts, double-check the jumper cables to make sure they are connected properly and securely. Sometimes a loose connection can prevent a successful jump start.
Once the Compass is successfully started, let it run for at least 10-15 minutes to allow the battery to fully recharge. It’s also a good idea to drive the vehicle around for a bit to ensure the battery is holding a charge. Remember, safety is key when jump starting a vehicle, so always follow the proper procedures and consult a professional if you are unsure.
Safety precautions to keep in mind while jumping the Compass
When jumping the Compass, it is essential to prioritize safety to avoid any accidents or damage to the vehicle. Here are some important precautions to keep in mind:
-
Ensure the Compass is on a flat surface: Before attempting to jump the vehicle, make sure it is parked on a level surface. This will help prevent the vehicle from rolling or shifting during the jump.
-
Use proper jump start cables: When connecting the Compass to another vehicle for a jump start, be sure to use high-quality, heavy-duty jump start cables. This will ensure a secure connection and reduce the risk of electrical issues.
-
Follow the correct jump start procedure: When jump-starting the Compass, always follow the proper procedure outlined in the owner’s manual. This will help prevent damage to the vehicle’s electrical system and ensure a successful jump start.
Frequently Asked Questions
Q: How can I jump start my 2018 Jeep Compass?
A: To jump start your 2018 Jeep Compass, you will need another vehicle with a charged battery and jumper cables.
Q: What is the correct procedure for jumping a 2018 Jeep Compass?
A: First, position the running vehicle next to the Jeep Compass. Then, attach the red positive jumper cable to the positive terminal on the dead battery and the other end to the positive terminal on the running vehicle’s battery. Next, attach the black negative jumper cable to the negative terminal on the running vehicle’s battery and the other end to a metal surface on the Jeep Compass that is not near the battery.
Q: How long should I let the running vehicle charge the dead battery in the Jeep Compass?
A: Allow the running vehicle to charge the dead battery for a few minutes before attempting to start the Jeep Compass.
Q: Are there any safety precautions I should take while jumping a 2018 Jeep Compass?
A: Be cautious of sparks when attaching the jumper cables, and make sure the vehicles are in park with the engines turned off before connecting the cables. Additionally, always follow the manufacturer’s guidelines for jumping a vehicle.
In Conclusion
mastering the art of jumping a 2018 Jeep Compass is a valuable skill to have in case of emergencies. By following the steps outlined in this guide, you can confidently navigate any unexpected mishaps that may arise. Remember to always prioritize safety and caution when dealing with car maintenance and repairs. Happy driving!